Clinical outcomes of single implant supported crowns utilising the titanium base abutment: A 7.5-year prospective cohort study.

OBJECTIVE: To assess radiographic, clinical and patient-reported outcomes of single zirconia implant-supported crowns on titanium base abutments (TBA) over a 7.5-year period. METHODS: Twenty-four patients received bone-level titanium implants and screw-retained zirconia implant crowns utilising TBA. Marginal bone level (MBL), clinical parameters (probing depth-PD, bleeding on probing-BoP, plaque control record-PCR), technical complications (USPHS criteria) and patient satisfaction were assessed at crown delivery (baseline), 1 year (FU-1) and at 7.5 years (FU-7.5) of follow-up. RESULTS: Eighteen patients were available for re-examination at 7.5 years. The mean MBL at FU-7.5 (0.35 ± 0.20mm) did not significantly change compared to baseline (0.54 ± 0.39, p=.352) and to FU-1 (0.54 ± 0.45mm, p=0.524). From baseline to 7.5 years, the mean PD increased significantly, from 3.0 ± 0.6mm to 3.7 ± 0.8mm (p=0.005). However, BoP and PCR did not significantly change; (BOP: from 27.1 ± 20.7% to 25.0 ± 20.0%, p=0.498; PCR: from 11.1 ± 21.2% to 25.0 ± 25.1%, p=0.100). Nine patients presented with more than one bleeding site. This denoted a peri-implant mucositis prevalence of 50%, whilst none of the implants presented peri-implantitis. One incidence of minor and major ceramic chipping were reported on 2 out of the 18 crowns, resulting in a prosthetic survival rate of 94.4%. Seventeen patients were highly satisfied with their result. CONCLUSION: Single implant-supported zirconia crowns on TBA displayed: (i) minor number of technical complications, (ii) high prosthetic survival rate, (iii) stable marginal bone level and (iv) high patient satisfaction at 7.5 years. CLINICAL IMPLICATIONS: Titanium base abutments despite their high use in clinical practice, lacked medium- and long-term studies. The presented findings highlight their clinical performance at 7.5 years as they display satisfying radiographic, clinical and patient-related outcomes. TBA appear to be a suitable abutment choice for medium-term implant-supported restorations.

Influence of polyether ether ketone coping crown on the adaptation of implant abutment.

OBJECTIVE: To evaluate the influence of polyether ether ketone coping crown on the adaptation of implant abutment. Methods: The vitro study was conducted at the department of Prosthodontics, Hainan Stomatological Hospital, China, from October 2021 to March 2022, and comprised patients undergoing implant surgery on first molar. Patients were divided into two groups, with group A patients receiving polyether ether ketone coping crowns, and group B receiving zirconia crowns. Replica technique was used to replicate the gap between the crowns and the abutments. The thickness of the silicone film was measured under the stereomicroscope, and the gap between the groups was compared. Data was analysed using SPSS 22. RESULTS: In group A, mean marginal gap was 82.43±25.00µm, and mean overall gap was 85.45±33.75µm. In group B, the corresponding values were 65.09±11.69µm and 78.04±26.67µm. There was a significant difference in the adaptation between the groups at the marginal and overall measurement points (p<0.05). Conclusion: Marginal and internal adaptations of polyether ether ketone coping crown for abutment could be considered clinically acceptable.

Formación de biopelícula bacteriana sobre las superficies de pilares de cicatrización de PEEK y titanio

Objetivos. Explorar el efecto de las características de superficie sobre el volumen total y la viabilidad de la biopelícula formada sobre pilares de cicatrización de PEEK y titanio. Métodos. Los parámetros de rugosidad (S a y S k) y la energía superficial de pilares de cicatrización de PEEK y titanio (n=3) fueron determinados mediante microscopía confocal láser de barrido (CLSM) y ángulo de contacto, respectivamente. Se determinó luego el volumen total y la viabilidad de una biopelícula bacteriana multiespecie cultivada por 30 días, mediante CLSM y el reactivo LIVE/DEAD Kit BacLight. El tamaño del efecto se determinó mediante d de Cohen. Resultados. Los pilares de PEEK mostraron una mayor rugosidad que los de titanio (S a 0,41 µm vs 0,17 µm), pero no se observaron diferencias en la energía superficial. Si bien el volumen total de biopelícula fue mayor en titanio que en PEEK (696 µm3 vs 419 µm3), no hubo diferencias en la proporción de bacterias vivas entre ambos materiales. Conclusiones. La viabilidad de la biopelícula bacteriana formada no guarda relación directa con las características superficiales de pilares de cicatrización de PEEK y titanio.

Objetivo. Explorar o efeito das características da superfície no volume total e viabilidade do biofilme formado em PEEK e pilares de cicatrização de titânio. Métodos. Parâmetros de rugosidade (S a e S k) e energia de superfície de PEEK e pilares de titânio (n = 3) foram determinados por microscopia confocal de varredura a laser (CLSM) e ângulo de contato, respectivamente. O volume total e a viabilidade de um biofilme bacteriano multiespécie cultivado por 30 dias foram então determinados usando CLSM e o reagente LIVE/DEAD Kit BacLight. O tamanho do efeito foi determinado usando o d de Cohen. Resultados. Os pilares de PEEK mostraram maior rugosidade do que os de titânio (S a 0,41 µm vs 0,17 µm), mas não foram observadas diferenças na energia de superfície. Embora o volume total de biofilme tenha sido maior no titânio do que no PEEK (696 µm3 vs 419 µm3), não houve diferenças na proporção de bactérias vivas entre os dois materiais. Conclusões. A viabilidade do biofilme bacteriano formado não está diretamente relacionada às características da superfície dos pilares de cicatrização de PEEK e titânio.

Objectives . To explore the effect of surface characteristics on the total volume and viability of a bacterial biofilm developed on the surface of PEEK and titanium healing abutments. Methods. Surface parameters S a and S k, as well as the surface energy of PEEK and titanium healing abutments (n=3) were determined using confocal laser scanning microscopy (CLSM) and contact angle, respectively. The total volume and viability of a multispecies bacterial biofilm cultivated for 30 days were determined using CLSM and the LIVE/DEAD BacLight reactive kit. Effect size was determined using Cohen's d. Results. PEEK healing abutments displayed a higher surface roughness than titanium (S a 0.41 µm vs 0.17 µm), although no differences in surface energy were observed. Despite the higher total volume of the biofilm measured on titanium abutments compared to PEEK (696 µm3 vs 419 µm3), no differences in the live/dead bacterial ratio were observed. Conclusions. Bacterial viability of the biofilm did not show a direct relation to the surface characteristics of PEEK and titanium healing abutments.

Clinical performance of single implant prostheses restored using titanium base abutments: A systematic review and meta-analysis.

PURPOSE: The aim of this review was to evaluate the survival rates of restorations utilizing titanium base abutments (TBA) for restoring single-unit implant prostheses. MATERIALS AND METHODS: This review was conducted following the preferred reporting items for systematic reviews and meta-analyses (PRISMA) guidelines. The focus question was: In patients who require the restoration of a single dental implant utilizing a titanium base abutment, what are the determining factors and outcomes relating to implant prosthesis prognosis and survival? A comprehensive search of databases (PubMed, EMBASE, and Cochrane Library) was conducted on 16 April 2023 and updated on 5 May 2023. Randomized clinical trials (RCT), retrospective studies and prospective studies, reporting on the use of TBA for single implant prostheses, were reviewed. A Cochrane collaboration risk of bias assessment analysis was performed for randomized clinical studies, and the Newcastle-Ottawa Scale tool was applied for non-randomized studies. A meta-analysis was performed on clinical trials reporting on survival rates of both TBA and other abutments. Other clinical studies, reporting on TBA only, were included for descriptive statistics. RESULTS: The search provided 1159 titles after duplicates were removed. Six RCTs were included to perform a meta-analysis and compare the survival of the TBA to other abutments [OR 0.74; 95% CI: 0.21-2.63, heterogeneity; I2 0%; p = .99]. Twenty-three prospective and retrospective studies fulfilled the criteria and were included in the meta-analysis after 12 months of function. A total of 857 single implant-supported prostheses fabricated with a TBA were included. TBA abutments have an estimate 98.6% survival rate after 1 year in function (95% CI: 97.9%-99.4%). The mean follow-up period was 31.2 ± 16.9 months. CONCLUSIONS: Single implant prosthesis restored with titanium base abutments showed favourable short-term survival rates.

The effect of different abutment materials on peri-implant tissues-A systematic review and meta-analysis.

OBJECTIVES: In patients with dental implants, what is the effect of transmucosal components made of materials other than titanium (alloys) compared to titanium (alloys) on the surrounding peri-implant tissues after at least 1 year? MATERIALS AND METHODS: This systematic review included eligible randomized controlled trials identified through an electronic search (Medline, Embase and Web of Science) comparing alternative abutment materials versus titanium (alloy) abutments with a minimum follow-up of 1 year and including at least 10 patients/group. Primary outcomes were peri-implant marginal bone level (MBL) and probing depth (PD), these were evaluated based on meta-analyses. Abutment survival, biological and technical complications and aesthetic outcomes were the secondary outcomes. The risk of bias was assessed with the RoB2-tool. This review is registered in PROSPERO with the number (CRD42022376487). RESULTS: From 5129 titles, 580 abstracts were selected, and 111 full-text articles were screened. Finally, 12 articles could be included. Concerning the primary outcomes (MBL and PD), no differences could be seen between titanium abutment and zirconia or alumina abutments, not after 1 year (MBL: zirconia: MD = -0.24, 95% CI: -0.65 to 0.16, alumina: MD = -0.06, 95% CI: -0.29 to 0.17) (PD: zirconia: MD = -0.06, 95% CI: -0.41 to 0.30, alumina: MD = -0.29, 95% CI: -0.96 to 0.38), nor after 5 years. Additionally, no differences were found concerning the biological complications and aesthetic outcomes. The most important technical finding was abutment fracture in the ceramic group and chipping of the veneering material. CONCLUSIONS: Biologically, titanium and zirconia abutments seem to function equally up to 5 years after placement.

Assessment of the alveolar bone loss in fresh socket implant procedures with immediate implant loading via temporary preformed anatomical healing caps: Comparison of two different lengths of the implant collar.

PURPOSES: The aim of the present clinical and radiologic retrospective study was to evaluate alveolar bone remodeling, in terms of alveolar width and peri­implant bone level, two years after immediate implant positioning (with two different collar lengths, 0.8 mm and 2.0 mm) and loading of preformed healing cap. The Null hypothesis, H0 is: there was no difference between the two groups of implants. METHODS: Patients suffering from single-tooth edentulous areas in premolar, cuspid, and incisive areas were treated with fresh-socket implants and immediate preformed anatomical healing caps. Each final crown restoration was fabricated 3 months later. Primary outcomes (related to loss of the alveolar width and peri­implant bone level) and secondary outcomes (testing adverse events, and measuring implant/prosthesis survival) were acquired and analyzed. RESULTS: A two-year retrospective analysis was conducted on 31 patients (19 female and 12 male), who underwent dental implant placement with implants having two different lengths of the collar: group A, 0.8 mm, and group B, 2.0 mm. As for the width of the alveolar crest, there was a negligible loss (less than half a millimeter) reported for both the groups, anyway reaching a statistical significance. Preoperative alveolar widths (9.50±0.67 mm and 9.45±0.90 mm, respectively for groups A and B) were different from the two-year alveolar widths (9.20±0.74 mm and 8.93±0.99 mm, respectively for groups A and B) with p-values ≤ 0.0049. When the marginal bone loss was assessed, significant differences were registered between the two procedure groups (-1.42±0.34 mm for group A and -0.11±0.15 mm for group B with a p-value < 0.0001). CONCLUSIONS: The proper design of a healing abutment was very important to preserve the emergence profile immediately after extraction and implant placement. The length of the implant collar used with an immediate healing abutment appeared to affect the preservation of the alveolar crest with predictable final results.

Preformed customized healing abutments in biologically oriented preparation technique procedure: a 3-year retrospective case-control study.

AIM: To determine the 3-year clinical and dimensional change of the soft tissue following implant placement in healed sites before and after loading with either customized or conventional healing abutments. MATERIALS AND METHODS: Premolar/molar implants were immediately loaded with either provisional and customized abutments without finishing lines according to principles of the Biologically Oriented Preparation Technique (BOPT), test group, or conventional healing abutments, control group. Three months later, the definitive crowns were fabricated. Primary outcomes (changes in the soft tissue) and secondary outcomes (adverse events) had been registered. RESULT: Fifty out of 87 subjects originally included were finally selected for this retrospective analysis: 23 in the test and 27 in the control group. During the first days after surgery 2 adverse events of mucositis, one for each group, occurred. A Few technical complications such as unscrewing 4 screw-retained crowns were recorded. A significant increase in the alveolar width was observed in both groups (test = +2.5±0.5mm, and control = +1.0±0.9mm). The widths appeared to not be merely changed from 3 months to 3 years in both groups. There were no significant differences regarding the width of the keratinized mucosa measured at baseline and after follow-up. Jemt papilla index showed a higher increase in the test group compared with that of the control group. CONCLUSION: Within 3 years of the follow-up period, peri-implant soft tissue outcomes of single, immediately loaded implants with customized healing abutments showed better results in terms of thickness and width when they were compared with those of the conventional group. Side effects count (mucositis and dehiscence) appeared to be very similar between the two groups. In addition, customized healing abutments led to significant augmentation of the alveolar width more than twice that registered in the conventional group.

Effect of inter-dental abutment distance on the impression accuracy of digital and conventional methods.

This study aimed to examine the effect of inter-dental abutment distance on the accuracy of digital and conventional impression methods. Five maxillary and mandibular models were prepared with different inter-dental abutment distances. Digital scans were obtained using an extraoral laboratory scanner as reference data. Each group was scanned 8 times using the intra-oral scanner for the digital method. For the conventional impression method, 8 additional silicone impression material was used to generate the stone casts from each group. Then casts were scanned. In the next step, stereolithography (STL) data was exported from the scans. The STL files were super-imposed on the reference scans using 3shape dental designer software to make the measurement. Kolmogorov-Smirnoff was used to determine if the data were normally distributed. In the digital impression method, as the abutment distance increased, the accuracy decreased. Various inter-dental abutment distances in digital groups showed significant differences (p=0.016) in impression accuracy, while the difference among conventional groups was not statistically significant (p=0.822). In the digital method, the mean inter-dental abutment between the 4-5 and 3-7 groups, 4-6 and 3-7 groups had a significant difference (p<0.05). However, the conventional method revealed no significant differences (p>0.05) between groups. In conclusion, when the inter-dental abutment distance exists and is surrounded by soft tissue, the possibility of error in the digital impression method is higher than in the conventional impression method.

Tactile misfit detection ability at the implant-abutment interface of internal connection dental implants: an in-vitro study.

OBJECTIVE: The aim of this in-vitro study was to investigate the tactile assessment ability at the implant impression-taking stage. METHODS: Thirty clinicians (18 novices, 12 experts) were included for a tactile fit assessment by using a used/new probe (tip diameter 100 µm/20 µm). Six implant replicas and related impression copings of two internal connection implant systems were used, each with a perfect fit (0 µm) and defined vertical micro gaps of 8, 24, 55, 110 and 220 µm at the interface. Statistical analysis was performed using descriptive methods and non-parametric tests with a focus on specificity (ability to detect perfect fit), sensitivity (ability to detect misfit), and predictive values. P-values <5% were considered statistically significant. RESULTS: The tactile assessment showed a mean total sensitivity for the Straumann and Nobel Biocare systems of 83% and 80% with a used probe, and 91% and 92% with a new probe, respectively. The mean total specificities were 33% and 20% with a used probe and 17% and 3% with a new probe, respectively. No statistical significance was observed between novice and expert clinicians concerning their tactile assessment ability. CONCLUSIONS: The ability to detect a perfect fit (specificity) with a probe was very poor for both implant systems and impaired with the use of a new probe. The use of a new probe improved the gap detection ability (sensitivity) significantly at the expense of the specificity. A combination of additional chairside techniques with training and calibration could improve clinicians' ability to correctly assess the fit/misfit at the implant-abutment interface.

Promoted Abutment-Soft Tissue Integration Around Self-Glazed Zirconia Surfaces with Nanotopography Fabricated by Additive 3D Gel Deposition.

Introduction: Improving the biological sealing around dental abutments could promote the long-term success of implants. Although titanium abutments have a wide range of clinical applications, they incur esthetic risks due to their color, especially in the esthetic zone. Currently, zirconia has been applied as an esthetic alternative material for implant abutments; however, zirconia is purported to be an inert biomaterial. How to improve the biological activities of zirconia has thus become a popular research topic. In this study, we presented a novel self-glazed zirconia (SZ) surface with nanotopography fabricated by additive 3D gel deposition and investigated its soft tissue integration capability compared to that of clinically used titanium and polished conventional zirconia surfaces. Materials and Methods: Three groups of disc samples were prepared for in vitro study and the three groups of abutment samples were prepared for in vivo study. The surface topography, roughness, wettability and chemical composition of the samples were examined. Moreover, we analyzed the effect of the three groups of samples on protein adsorption and on the biological behavior of human gingival keratinocytes (HGKs) and human gingival fibroblasts (HGFs). Furthermore, we conducted an in vivo study in which the bilateral mandibular anterior teeth of rabbits were extracted and replaced with implants and corresponding abutments. Results: The surface of SZ showed a unique nanotopography with nm range roughness and a greater ability to absorb protein. The promoted expression of adhesion molecules in both HGKs and HGFs was observed on the SZ surface compared to the surfaces of Ti and PCZ, while the cell viability and proliferation of HGKs and the number of HGFs adhesion were not significant among all groups. In vivo results showed that the SZ abutment formed strong biological sealing at the abutment-soft tissue interface and exhibited markedly more hemidesmosomes when observed with a transmission electron microscope. Conclusion: These results demonstrated that the novel SZ surface with nanotopography promoted soft tissue integration, suggesting its promising application as a zirconia surface for the dental abutment.

Reasons for the fatigue of ball attachments and their O-rings: A systematic review.

The ball attachments and their O-rings used for the retention and stabilization of overdentures showed a decrease in retention as the number of cycles increased. This fact resulted in a decrease in the retention of the prosthesis. The purpose of this study was to evaluate the fatigue resistance of ball attachments through a systematic review. An electronic search was performed using the Cochrane Library, LILACS, PubMed, ScienceDirect, and Web of Science databases. The search was conducted based on the PICOS framework. The inclusion criteria involved in the search comprised research articles written in English and published between the years 2000 and 2020. In the final selection, 18 articles were included in the review. Most of these studies performed the fatigue retention tests using parallel implants without angles. However, some studies used different angles to analyze the fatigue retention values. With the passage of time, the wear results in deformation and, as a consequence, a decrease in the retention of most attachments, leading to treatment failure. The main factor to be considered is the loss of retention of these components and their low durability. The loss of retention is due to large extent to the materials used to manufacture the attachments and O-rings, the size and angulation of the implants, and the length of the prosthesis. Future research is needed to further elucidate the reasons for the failure of the attachments.

Physical and mechanical changes on titanium base of three different types of hybrid abutment after cyclic loading.

PURPOSE: This study investigated the physical and mechanical changes in the titanium base of three different hybrid abutment materials after cyclic loading by estimating the post-load reverse torque value (RTV), compressive side fulcrum wear pattern of titanium base, and surface roughness. MATERIALS AND METHODS: A total of 24 dental implants were divided into three groups (n = 8 each): Group Z, LD, and P used zirconia, lithium disilicate, and polyetheretherketone, respectively, for hybrid abutment fabrication. RTV was evaluated after cyclic loading with 50 N for 1.2 × 106 chewing cycles. The compressive sides of the titanium bases were analyzed using a scanning electron microscope, and the roughness of the affected areas was measured using an optical profilometer after loading. Datasets were analyzed using Kruskal-Wallis test followed by Mann-Whitney tests with the Bonferroni correction (α = .05). RESULTS: Twenty-three samples passed the test; one LD sample fractured after 770,474 cycles. Post-load RTV varied significantly depending on the hybrid-abutment material (P = .020). Group P had a significantly higher median of post-load RTVs than group Z (16.5 and 14.3 Ncm, respectively). Groups LD and P showed minor signs of wear, and group Z showed a more pronounced wear pattern. While evaluating compressive side affected area roughness of titanium bases, lower medians were shown in group LD (Ra 0.16 and Rq 0.22 µm) and group P (Ra 0.16 and Rq 0.23 µm) than in group Z (Ra 0.26 and Rq 0.34 µm); significant differences were found only among the unaffected surface and group Z. CONCLUSION: The hybrid abutment material influences the post-load RTV. Group Z had a more pronounced wear pattern on the compressive side of titanium base; however, the surface roughness was not statistically different among the hybrid-abutment groups.

Implant connection and abutment selection as a predisposing and/or precipitating factor for peri-implant diseases: A review.

Peri-implant mucosal integration is becoming a critical aspect for long term implant health and can be triggered the selection of implant components. The aim of this review is therefore to investigate the evidence concerning implant connection and abutment characteristics (abutment materials, design, handling) as predisposing or precipitating factor for peri-implant mucositis and peri-implantitis. Although the evidence that these features can directly predispose/precipitate peri-implant diseases is limited, there are -few- studies showing a potential role of the implant connection, trans-mucosal configuration, and handling in the development of early bone loss and/or peri-implantitis. With bone level implants, conical internal connections (with inherent platform switching) might be preferred over internal flat-flat and external connections to decrease the risk of early bone loss and potentially the risk of peri-implant disease. Moreover, there is a trend suggesting moving the prosthetic interface coronally (to the juxta-mucosal level) as soon as possible to reduce the number of disconnections and to limit the risk of cements remnants. This can be achieved by choosing a tissue-level implant or to place a trans-mucosal abutment (one abutment-one time approach) to optimize the peri-implant soft tissue seal. In absence of evidence for the biocompatibility regarding several restorative materials, biocompatible materials such as titanium or zirconia should be preferred in the trans-mucosal portion. Finally, higher implants (≥2mm) with an emergence angle below 30° seem more favourable. It should however be noted that some of this information is solely based on indirect information (such as early bone loss) and more research is needed before making firm recommendations about abutment choice. [Correction added on 13 March 2023, after first online publication: 'longer implants (≥2mm)' was changed to 'higher implants (≥2mm)' in this version.].

Biomaterials and Clinical Applications of Customized Healing Abutment-A Narrative Review.

Customized healing abutments have been introduced in clinical practice along with implant surgery to preserve or create natural-appearing hard and soft tissue around the implant. This provides the benefits of reducing the overall treatment time by eliminating the second stage and reducing the elapsed time of the fabrication of the final prostheses. This article aims to review the types and properties of materials used for the fabrication of customized healing abutments and their clinical applications. Articles published in English on customized healing abutments were searched in Google Scholar, PubMed/MEDLINE, ScienceDirect, and the Scopus databases up to August 2022. The relevant articles were selected and included in this literature review. Customized healing abutments can be fabricated from materials available for dental implants, including PEEK, PMMA, zirconia, resin composite, and titanium. All the materials can be used following both immediate and delayed implant placement. Each material provides different mechanical and biological properties that influence the peri-implant tissues. In conclusion, the studies have demonstrated promising outcomes for all the materials. However, further investigation comparing the effects of each material on peri-implant soft and hard tissues is required.

Is the Diagnosis of Generalized Stage IV (Severe) Periodontitis Compatible with the Survival of Extended Stabilizing Prosthetic Restorations? A Medium-Term Retrospective Study.

The aim of the study was to identify the most relevant patient-related factors directly involved (alone or in combinations) in the long-term survival and functionality of the abutment teeth of extensive stabilizing bridges and removable prosthesis, in patients treated for Stage IV periodontitis, adhering to SPT over a period of at least 5 years. Seventy-six patients treated between 2000-2022, rehabilitated with FDPs and RDPs, adhering to SPT for at least 5 years were included. Patient-related factors influencing retention of RDPs and FDP, survival rates in regular (RCs) and irregular compliers (ICs), and incidence of biological and technical complications were assessed. During a follow-up of 69 months, from 57 patients with FDPs and 19 patients with RDPs, 39 (51.32%) were ICs, while 37 (48.68%) were RCs. An overall statistically significant association (p = 0.04) was identified between biological complications and the type of prostheses. The RDP patients had more complications than FDP patients. In 5.26% of the RDP patients, root caries were identified, and 10.53% were diagnosed with a periapical (endodontic) lesion, while 3.51% of the FDPS patients presented root caries. In five (6.57%) cases, abutment loss resulted in the loss of the prosthesis. Statistically significant correlations were observed between systemic diseases and tooth loss, and between type of tooth lost and the reason for tooth loss, irrespective of the type of prosthesis. A total of 66.67% of the lost incisors, 85.71% of the lost premolars, and 88.89% of the lost molars occurred due to periodontal causes. Furthermore, 93% of the FDPs and RDPs were still in place and in function.

Abutment mechanical complications of a Morse taper connection implant system: A 1- to 9-year retrospective study.

BACKGROUND: The fracture of a Morse tapered abutment connection in an osseointegrated implant is one of the most serious mechanical complications, and it is extremely hard to deal with this complication in clinical practice. PURPOSE: The aim of this study was to explore the cumulative mechanical complications focus on abutment of a platform switching Morse taper connection implant system after loading, and to perform a retrospective, approximately 1- to 9-year follow-up study to identify the predisposing factors. MATERIALS AND METHODS: A total of 495 patients with 945 fitted implants were enrolled in this study with a follow-up from January 2012 to January 2020. The data of mechanical complications of the abutment, including abutment fracture (AF) and abutment screw loosening (ASL), and possible causative factors were extracted and evaluated statistically. RESULTS: A total of 25 out of 945 (2.65%) cumulative abutment mechanical complications occurred. AF was the most common complication (n = 13, 1.38%), followed by ASL (n = 12, 1.27%). For AF, gender, type of prosthesis, abutment design, and implant diameter were identified as the causative factors. AF was mostly observed in the single crown of males in molar areas, while ASL was more likely to occur on an angled abutment than on a non-angled abutment. Moreover, the abutment with the positioning index (/X) had a higher incidence of fracture than the abutment without the positioning index (C/). CONCLUSIONS: This study shows that the Morse taper connection is a safe abutment connection. AF occurs more frequently within single crowns in molar area of males, especially with the positioning index (/X), while ASL is more likely to occur in an angled abutment.

Effect Morphology and Surface Treatment of the Abutments of Dental Implants on the Dimension and Health of Peri-Implant Biological Space.

STATEMENT OF THE PROBLEM: The gingival configuration around implant abutments is of paramount importance for preserving the underlying marginal bone, and hence for the long-term success of dental implants. OBJECTIVE: The objective was to study, clinically and histologically, the effects of the change in the morphology of abutments connected to the endosseous implant, and of their surface treatment. In particular, the objective was to ascertain the effect of changing the shape of the transepithelial pillar and the treatment of its surface on the dimensions, quality and health of the components of the peri-implant biological space, such as the dimensions of the epithelial and connective tissues of the biological space, the concentration of inflammatory cells and the density of collagen fibers. METHODS: A clinical trial of 10 patients with a totally edentulous maxilla, who had four implants (IPX4010_GALIMPLANT®, Sarria, Spain) inserted in the area of the first and second molars on both sides with computer-guided implant surgery, was conducted with the final purpose of assessing the quality of the peri-implant soft tissue attachment around the transepithelial abutments which were employed (aesthetic machined (RM), aesthetic anodized (RA), slim machined (SM) and slim anodized (SA)). At 8 weeks and following the collection of the samples (removal of the implant-abutment assembly with its surrounding hard and soft tissue) and their processing for subsequent histological and histomorphometric analysis in order to study the dimensions, quality and health of the peri-implant soft tissue area, the variables previously mentioned were determined according to the aims of the study. By using appropriate diameter trephine in order to obtain a useful fringe of soft tissue around the transepithelial pillars, ANOVA and chi-square tests were performed. RESULTS: The SPSS statistical analysis ANOVA results revealed that the machined slim abutments have a better performance considering the variables analyzed with epithelial and connective attachment heights of 1.52 mm and 2.3 mm, respectively, and that connective density (density of collagen fibers) was high at 85.7% of the sample size affected by the design for the slim abutments and 92.9% of the high-density sample size affected by the surface treatment for the machined surface. CONCLUSIONS: All variables studied, despite the small sample size, showed the superiority of the slim machined abutment among the four groups.

A comparative biomechanical study of original and compatible titanium bases: evaluation of screw loosening and 3D-crown displacement following cyclic loading analysis.

PURPOSE: This study evaluated screw loosening and 3D crown displacement after cyclic loading of implant-supported incisor crowns cemented with original titanium bases or with three compatible, nonoriginal components. MATERIALS AND METHODS: A total of 32 dental implants were divided into four groups (n = 8 each): Group 1 used original titanium bases, while Groups 2-4 used compatible components. The reverse torque value (RTV) was evaluated prior to and after cyclic loading (1,200,000 cycles). Samples (prior to and after cyclic loading) were scanned with a microcomputed tomography (micro-CT). Preload and postload files were superimposed by 3D inspection software, and 3D crown displacement analysis was performed using root-mean-square (RMS) values. All datasets were analyzed using one-way ANOVA and Tukey's post hoc analysis. RESULTS: Significant variations were observed in the postload RTV, depending on the titanium base brand (P < .001). The mean postload RTVs were significantly higher in Groups 1 and 2 than in the other study groups. While evaluating 3D crown displacement, the lowest mean RMS value was shown in the original Group 1, with the highest RMS value occurring in Group 4. CONCLUSION: Within the limitations of this in vitro study and under the implemented conditions, it was concluded that the manufacturer brand of the titanium base significantly influenced screw loosening following the fatigue test and influenced 3D crown displacement after cyclic loading.

Inflammatory effects of individualized abutments bonded onto titanium base on peri-implant tissue health: A randomized controlled clinical trial.

BACKGROUND: In implant prosthodontics, computer-assisted design and computer-assisted manufacturing (CAD/CAM) zirconia abutments bonded onto titanium bases are frequently used in prosthetic dentistry. Unpolymerized monomer of the bonding material or the adhesive gap itself may have a negative effect on peri-implant tissue health. However, evidence addressing this problem is not available. PURPOSE: The aim of the current trial was to study inflammatory effects of individualized abutments bonded onto titanium bases. MATERIAL AND METHOD: A total of 24 patients with one test abutment and one control abutment each participated in this prospective, double-blind, randomized controlled clinical trial. Thereby, test abutments were CAD/CAM titanium abutments bonded onto titanium abutments (Ti-Base). As control abutments individualized, one-piece CAD/CAM titanium abutments were used. At abutment installation as well as 6 and 12 months thereafter bone level changes, clinical parameters as well as Il-1ß levels were assessed. RESULTS: Neither for bone level or clinical parameters nor for Il-1ß levels, significant differences between test and control abutments could be found. However, in both groups Il-1ß levels were significantly elevated at both the 6 and 12 months follow-up compared to baseline. CONCLUSION: Within the limits of this RCT, it can be concluded that effects on the inflammatory state of peri-implant tissues do not differ between individualized abutments bonded onto Ti-Bases and individualized one-piece abutments.

Influence of Platform Switching, Abutment Design and Connection Protocols on the Stability of Peri-Implant Tissues. A Systematic Review.

PURPOSE: To appraise the effect of abutment factors namely platform switching, design and connection protocols on the stability of peri-implant tissues. MATERIALS AND METHODS: An electronic and hand search were conducted. Randomized control trials and controlled prospective studies of at least one-year follow-up, published in the last 12 years, were included. RESULTS: Initial electronic database search generated 3054 studies, while individual journal and hand searching resulted in 232 articles. Sixty-three publications were selected for full text analysis based on inclusion and exclusion criteria. Nineteen articles investigated platform switching. Fourteen studies reported positive influence of platform switching while five studies did not find a significant difference in bone loss compared to platform matched abutments. Two articles reported on concave abutments and found no advantage over conventional abutments. Seven studies investigated "one-abutment-one-time protocol", two found comparable results to multiple abutment disconnections while five studies suggested better soft and hard tissue maintenance. The risk of bias was unclear or high in most studies. CONCLUSION: Platform switched abutments may reduce crestal bone loss during the first year. There is insufficient evidence to suggest better clinical outcomes of concave abutment. There is insufficient evidence to indicate the superiority of 'one abutment-one-time protocol'.